From a5cf93b8d678ce3d5ecce1eab174f09dbe85b8d5 Mon Sep 17 00:00:00 2001
From: XANTRONIX Development
Date: Thu, 16 Nov 2023 17:15:15 -0500
Subject: Might be good?

---
 case/top.scad | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

(limited to 'case')

diff --git a/case/top.scad b/case/top.scad
index 3fcbd6a..44f4ba1 100644
--- a/case/top.scad
+++ b/case/top.scad
@@ -107,8 +107,8 @@ module top_case(key_switch_sizes, pcb_screw_holes) {
         ];
 
         for (post = posts) {
-            translate([post[0], post[1], wall_height - wall_width - post[2]])
-            screw_post(post[2]);
+            translate([post[0], post[1], wall_height - wall_width - post[2] - eps])
+            screw_post(post[2] + eps);
         }
     }
 
@@ -196,22 +196,22 @@ module top_case(key_switch_sizes, pcb_screw_holes) {
 
         for (x = [0: support_x_interval: keyboard_width + 2 * wall_width]) {
             translate([support_x_offset + x,
-                       upper_support_y_offset,
+                       upper_support_y_offset - eps,
                        wall_height - wall_width])
-            support([upper_support_length, keyboard_switch_height], support_width);
+            support([upper_support_length + 2*eps, keyboard_switch_height], support_width);
 
             translate([support_x_offset + x,
-                       lower_support_y_offset,
+                       lower_support_y_offset - eps,
                        wall_height - wall_width])
-            support([lower_support_length, keyboard_switch_height], support_width);
+            support([lower_support_length + 2*eps, keyboard_switch_height], support_width);
         }
 
         for (y = [0: support_y_interval: keyboard_length + 2 * wall_width]) {
-            translate([right_support_x_offset,
+            translate([right_support_x_offset - eps,
                        support_y_offset + y - wall_width + support_width,
                        wall_height - wall_width])
             rotate([0, 0, -90])
-            support([right_support_length, keyboard_switch_height], support_width);
+            support([right_support_length + 2*eps, keyboard_switch_height], support_width);
 
             translate([left_support_x_offset - eps,
                        support_y_offset + y - wall_width + support_width,
@@ -227,17 +227,17 @@ module top_case(key_switch_sizes, pcb_screw_holes) {
 
         /* Upper */
         translate([0, case_length_bottom - wall_width, 0])
-        cube([case_width_bottom, wall_width, wall_height - wall_width], false);
+        cube([case_width_bottom, wall_width, wall_height], false);
 
         /* Right */
         translate([case_width_bottom - wall_width, 0, 0])
-        cube([wall_width, case_length_bottom, wall_height - wall_width], false);
+        cube([wall_width, case_length_bottom, wall_height], false);
 
         /* Lower */
-        cube([case_width_bottom, wall_width, wall_height - wall_width], false);
+        cube([case_width_bottom, wall_width, wall_height], false);
 
         /* Left */
-        cube([wall_width, case_length_bottom, wall_height - wall_width], false);
+        cube([wall_width, case_length_bottom, wall_height], false);
     }
 
     module screw_holes() {
-- 
cgit v1.2.3