diff options
| -rw-r--r-- | case/case.scad | 95 |
1 files changed, 48 insertions, 47 deletions
diff --git a/case/case.scad b/case/case.scad index 0a7fd6f..3a93290 100644 --- a/case/case.scad +++ b/case/case.scad @@ -110,83 +110,67 @@ module keyboard_base_plate(pcb_width, pcb_length) { /* Upper wall */ side([-pcb_clearance_edge - thickness + corner_radius, pcb_clearance_edge + pcb_length, - 0], - [wall_width, thickness, wall_height]); + -thickness + corner_radius], + [wall_width, thickness, wall_height + thickness - corner_radius]); /* Right wall */ side([ pcb_clearance_edge + pcb_width, -pcb_clearance_edge - thickness + corner_radius, - 0], - [thickness, wall_length, wall_height]); + -thickness + corner_radius], + [thickness, wall_length, wall_height + thickness - corner_radius]); /* Lower wall */ side([-pcb_clearance_edge - thickness + corner_radius, -pcb_clearance_edge - thickness, - 0], - [wall_width, thickness, wall_height]); + -thickness + corner_radius], + [wall_width, thickness, wall_height + thickness - corner_radius]); /* Left wall */ side([-pcb_clearance_edge - thickness, -pcb_clearance_edge - thickness + corner_radius, - 0], - [thickness, wall_length, wall_height]); + -thickness + corner_radius], + [thickness, wall_length, wall_height + thickness - corner_radius]); /* Upper right wall corner */ wall_corner([thickness + pcb_clearance_edge + pcb_width - corner_radius, thickness + pcb_clearance_edge + pcb_length - corner_radius, - 0], + -thickness + corner_radius], [0, 0, 0], corner_radius, - wall_height); + wall_height + thickness - corner_radius); /* Lower right wall corner */ wall_corner([ thickness + pcb_clearance_edge + pcb_width - corner_radius, 0 - thickness - pcb_clearance_edge + corner_radius, - 0], + -thickness + corner_radius], [0, 0, 270], corner_radius, - wall_height); + wall_height + thickness - corner_radius); /* Lower left wall corner */ wall_corner([-pcb_clearance_edge - thickness + corner_radius, -pcb_clearance_edge - thickness + corner_radius, - 0], + -thickness + corner_radius], [0, 0, 180], corner_radius, - wall_height); + wall_height + thickness - corner_radius); /* Upper left wall corner */ wall_corner([-pcb_clearance_edge - thickness + corner_radius, pcb_clearance_edge + pcb_length + thickness - corner_radius, - 0], + -thickness + corner_radius], [0, 0, 90], corner_radius, - wall_height); + wall_height + thickness - corner_radius); - /* Upper right corner */ - /*round_corner([pcb_clearance_edge + thickness + pcb_width - corner_radius, - pcb_clearance_edge + thickness + pcb_length - corner_radius, - -thickness/2], - [90, 90, 90]);*/ - - /* Lower right corner */ - /*round_corner([ pcb_clearance_edge + thickness + pcb_width - corner_radius, - -pcb_clearance_edge - thickness + corner_radius, - -thickness/2], - [180, 90, 90]);*/ - - /* Lower left corner */ - /*round_corner([-pcb_clearance_edge - thickness + corner_radius, - -pcb_clearance_edge - thickness + corner_radius, - -thickness/2], - [-90, 90, 90]);*/ - - /* Upper left corner */ - /*round_corner([-pcb_clearance_edge - thickness + corner_radius, - pcb_clearance_edge + thickness + pcb_length - corner_radius, - -thickness/2], - [0, 90, 90]);*/ - + /* Bottom plate */ + side([-pcb_clearance_edge - thickness + corner_radius, + -pcb_clearance_edge - thickness + corner_radius, + -thickness], + [bottom_width + 2 * thickness - 2 * corner_radius, + bottom_length + 2 * thickness - 2 * corner_radius, + thickness]); + /* Upper edge */ /*round_edge([0 - thickness - pcb_clearance_edge + corner_radius, thickness + pcb_clearance_edge + pcb_length - corner_radius, @@ -215,13 +199,30 @@ module keyboard_base_plate(pcb_width, pcb_length) { [270, 90, 0], bottom_length + 2 * corner_radius);*/ - /* Bottom plate */ - /*side([-pcb_clearance_edge - corner_radius, - -pcb_clearance_edge - corner_radius, - -thickness], - [bottom_width + 2 * corner_radius, - bottom_length + 2 * corner_radius, thickness]);*/ - + /* Upper right corner */ + /*round_corner([pcb_clearance_edge + thickness + pcb_width - corner_radius, + pcb_clearance_edge + thickness + pcb_length - corner_radius, + -thickness/2], + [90, 90, 90]);*/ + + /* Lower right corner */ + /*round_corner([ pcb_clearance_edge + thickness + pcb_width - corner_radius, + -pcb_clearance_edge - thickness + corner_radius, + -thickness/2], + [180, 90, 90]);*/ + + /* Lower left corner */ + /*round_corner([-pcb_clearance_edge - thickness + corner_radius, + -pcb_clearance_edge - thickness + corner_radius, + -thickness/2], + [-90, 90, 90]);*/ + + /* Upper left corner */ + /*round_corner([-pcb_clearance_edge - thickness + corner_radius, + pcb_clearance_edge + thickness + pcb_length - corner_radius, + -thickness/2], + [0, 90, 90]);*/ + /* Screw holes */ /*for (screw_hole = screw_holes) { screw_post([screw_hole[0], screw_hole[1], 0], |